Improvement of sticking problem in TPE/TPR/TPU/TPV materials during injection molding 2018/12/14 19:19

       TPE/TPR/TPU/TPV thermoplastic elastomer soft rubber materials are more common in the injection molding process, especially in the case of low hardness, TPE/TPR/TPU hardness is lower than 60A, TPV hardness is lower than 40A, the sticking problem is quite common, and the main sticking modes take two forms:

1. Thermoplastic elastomer in the mainstream mold
       Since the main flow path is the closest position to the injection nozzle, the pressure exerted by the screw injection is the largest, resulting in the smallest material shrinkage in this area, whereby the material and the inner wall of the gate slide to generate greater friction.
       The specific solution is as follows:
       1.1. Because of the particularity of the thermoplastic elastomer material, the smoother the surface of the mold, the greater the adsorption force, which is exactly the opposite of the hard plastic. Therefore, the gate bushing can be subjected to electrical discharge machining to retain a certain thickness of the discharge pattern and reduce the flow path. Adsorption force
       1.2. The ejector pin of the flow channel adopts the inverted shape of the flow groove pin pattern, which increases the force of pulling the flow channel. There is no need to worry about the reverse buckle, the flow channel will not be taken out, because this is a soft glue, of course, the angle of the reverse buckle can be started from a small Slowly experiment, if a general Z-shaped needle is used, there is a possibility that the pulling force is insufficient, resulting in a flow path sticking master.
Second, thermoplastic elastomer injection molding products
       Compared with the main gate sticking mold, the probability of the product sticking mold is low. Usually, the product sticking mold occurs in the product structure design, such as the male mold drawing angle is too large, the male mold needs the skin pattern processing and the like.
       The specific solution is as follows:
       2.1. The male mold is polished to a mirror surface as much as possible to increase the adsorption force, which is also contrary to the hard plastic;
       2.2. The draft angle of the male mold can be made small in size, or simply not drafted, and if allowed, can even be reversed;
       2.3. The thimble head can be provided with a cross rib;
       2.4. From the aspect of molding process, the master mold can be connected to a high mold temperature, and the male mold can be connected to a low mold;
       2.5. Adjusting the formulation of the thermoplastic elastomer material to lower the injection molding process temperature;
       2.6. Reduce the pressure of holding pressure;
       2.7. Before the molding, the mold release agent is sprayed in the cavity.
       Under normal circumstances, the thermoplastic elastomer is molded on the mold after bonding, which is the first mainstream mold and the second case described above.
       However, sometimes due to materials, process parameter settings or mold design reasons, the product will stick to the front mold (such as the front mold has a large adsorption force), it is difficult to demould, and even the product is deformed or pulled, and may be due to the main casting. The problem of sticking to the mouth is generally caused by the pressure of the holding pressure being too large. This will also create a gate problem.
       For thermoplastic elastomers with a medium hardness or higher, the depth of the dermatoglyphics is increased, and on the contrary, it is easy to form a sticking mold, which requires attention. Third, improve the sticking problem from the perspective of thermoplastic elastomer material formulation
       3.1. Adding an external lubricant to the thermoplastic elastomer elastomer material, such as silicone, oleic acid amide, erucamide, EBS, etc.;
       3.2. Reduce the addition of softening oil, relatively straight paraffin oil is better;
       3.3. Increasing the crystallization temperature and crystallization rate of the continuous phase material;
       3.4. Add some filler when possible.
Remarks：
       For horizontal injection molding machines, Taiwan and Japan are generally called male and female molds. Hong Kong is generally called front and back molds. In China, there are also called dynamic molds and fixed molds, that is: male mold = back mold = moving Mode, master = front mode = fixed mode.